This article was co-authored by James Schuelke and by staff writer, Eric McClure. James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing experience and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.
It's time to replace your sink stopper—but with all the parts and pieces around and below your sink drain, you aren't completely sure how to get started. As far as home repairs go, replacing a pop-up sink stopper is pretty low on the difficulty curve, and we're here to walk you through everything you need to know. Read on to learn exactly how to remove the old stopper, disconnect and install a new drain, and install your new stopper. In no time at all, your sink stopper will be ready to go!
This article was co-authored by James Schuelke and by staff writer, Eric McClure. James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing experience and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest. This article has been viewed 353, 357 times.
What To Do When Your Sink Stopper Is Stuck
To replace a sink stopper, first, follow the vertical bar of the stopper beneath your sink. Then, undo the clamp that connects the bar to the angled rod that enters the drainpipe by pinching and separating it. After that, unscrew the nut holding the angled rod and pull it off. Undo the screw holding the extension bar and lift out the drain stopper. To install the new stopper, push the new sink drain into the opening and tighten the nut to secure it in place. Then, go beneath the sink to reconnect the angled pivot rod to the extension bar, and tighten all of the nuts. Test the stopper and check beneath the sink to make sure there aren’t any leaks. For tips about how to undo the tailpipe, keep reading!We recommend the best products through an independent review process, and advertisers do not influence our picks. We may receive compensation if you visit partners we recommend. Read our advertiser disclosure for more info.
Jonathon Jachura is a two-time homeowner with hands-on experience with HVAC, gutters, plumbing, lawn care, pest control, and other aspects of owning a home. He is passionate about home maintenance and finding the best services. His main goal is to educate others with crisp, concise descriptions that any homeowner can use. Jon uses his strong technical background to create engaging, easy-to-read, and informative guides. He does most of his home and lawn projects himself but hires professional companies for the “big things.” He knows what goes into finding the best service providers and contractors. Jon studied mechanical engineering at Purdue University in Indiana and worked in the HVAC industry for 12 years. Between his various home improvement projects, he enjoys the outdoors, a good cup of coffee, and spending time with his family.
Lora Novak meticulously proofreads and edits all commercial content for Today’s Homeowner to guarantee that it contains the most up-to-date information. Lora brings over 12 years of writing, editing, and digital marketing expertise. She’s worked on thousands of articles related to heating, air conditioning, ventilation, roofing, plumbing, lawn/garden, pest control, insurance, and other general homeownership topics.
How To Unblock A Bathroom Sink
Today’s Homeowner exists to help you maintain or improve your home safely and effectively. We uphold strict editorial standards and carefully vet the advice and resources referenced in our articles. Click below to learn more about our review process and how we earn money.
Sink stoppers are a crucial piece of a sink setup. But when clogs throw a wrench in your plans, you need to know how to remove your sink stopper. They can be tricky to remove, but without them, you wouldn’t be able to trap water in the sink for various tasks from washing dishes to cleaning makeup brushes.
There are four common types of sink stoppers: pop-up, push-pull, flip-it, and toe-touch. Each stopper has a unique removal method, with some more difficult than others. In most cases, you can complete the project with nothing more than basic tools including pliers, channel-lock pliers, or a screwdriver.
How To Remove A Sink Stopper
This article explores the removal processes for each type of sink stopper in a few simple steps. It’s important to note that while most removal processes are easy, some are more complex and may require the help of a skilled plumber.
Pop-up sink stoppers (drain plugs) are a common feature in bathroom sinks. They operate using a more complex mechanism than other stoppers we’ll discuss, employing clevis straps, pivot rods, spring clips, and gaskets to get the job done.
When you pull up on the rod at the back of the faucet, the mechanism pulls the stopper downward, using the gasket to create a tight seal against the sink. When you push the rod down, it raises the stopper, lifting the gasket away from the sink and allowing water to drain.
Amazon.com: Pop Up Bathroom Sink Drain
First, find the lift rod and clevis strap underneath the bathroom or kitchen sink. If you have a cramped base cabinet, clean it out and set stored objects aside before attempting to access the drain assembly.
Next, you’ll need to unscrew the pivot rod from the drain pipe. When you remove the pivot rod, the sink stopper will drop into the drain, becoming flush with the sink and making it difficult to lift it out. Hold the stopper with one hand or place something underneath the lip to prevent it from sliding down when you remove the pivot rod.
When you’re ready, unthread the nut connecting the pivot rod to the drain pipe. You may need to use channel-lock pliers to loosen the nut, although this will depend on how snugly it’s attached. Once you loosen the nut, work the pivot rod backward and pull it out of the drain pipe.
How To Use A Drain Snake To Clear Clogged Sinks And Showers
After you remove the pivot rod from the drain pipe, the sink stopper can move freely in the drain. Lift it out of the drain opening by pulling up on the stopper. It should come out without resistance unless there’s a clog, as the pivot rod is what fixes it in place. If your drain is clogged or drains slowly, you can use a drain snake to remove any debris stuck in the pipe before you reinstall the sink stopper.
While you have the assembly out, clean any hair, gunk, or grime off the end of the pivot rod. Wash the stopper with cleaner and a scrub brush, ensuring you remove all gunk and debris.
Examine each component for signs of damage or wear, replacing each part as necessary. When you’re done, reassemble the sink stopper if necessary. To reinstall the stopper, fit the stopper back into the drain. Insert the pivot rod into the drain pipe and feed it through the hole at the bottom of the stopper.
How To Unclog A Bathroom Sink With Sink Stopper
This step can take some trial and error, but you’ll know when you’ve attached it correctly when you can operate the drain as usual. Once you hook the stopper with the pivot rod, tighten the nut in place to secure the assembly.
A push-pull sink stopper looks similar to a lift-and-turn stopper, often featuring a knob atop the stopper. The smooth, wide knob is fixed in place, allowing users to pull the stopper up or push it into place, hence the name. These stoppers have an incredibly simple mechanism, so removing them is easy — just follow the steps below.
Some push-pull sink stoppers have a detachable knob. To remove these models, you’ll need to remove the knob to access the mounting post. Simply grip the drain stopper in one hand and the knob in the other.
Unclog A Sink, Shower Or Tub Drain
Once you reveal the fastening bolt, use a screwdriver or pliers to unthread the bolt from the drain crossbar. After unthreading the stopper, you can lift it out of the drain.
If you have a push-pull stopper without a detachable knob, the process is similar but doesn’t require as many steps. Instead of unthreading the knob to expose the fastening bolt, you can unthread the entire piece at once. Simply twist the entire drain stopper counterclockwise to unthread the hidden bolt from the drain crossbar.
After you take the sink stopper out of the drain, inspect it for damage or debris. In many cases, hair, soap scum, and other grime build up on the stopper. While you have the stopper out, give it a good scrubbing with a brush and some cleaner.
How To Unclog A Kitchen Sink
After cleaning the stopper and completing tasks that require the stopper out of the way, reinstall the stopper by retracing your steps.
Flip-it sink stoppers feature a flip lever that allows the gasket within the drain to expand or contract. When you flip the stopper into the open position, the gasket contracts, allowing water to flow through. When you flip the stopper into
0 Comments
Posting Komentar