Have you ever needed to know How to Replace a Sink Drain? Or maybe in the past you hired a plumber. Well, I’m here today to tell you that it’s not a hard project and I know you can do it!
I think the plumbing Gods smiled down on me recently. After the little leak that turned into a major kitchen renovation, finding this crack in the drain pipe saved us from another costly leak.
I don’t normally inspect the drain pipes on our sinks, but I just happen to be looking for something under my sons’ sink when I noticed the crack on the drain pipe. Remarkably, there were no drips in the vanity. Before I could grab a new drain assembly, I gently hinted to the family that they might want to use another sink in the house. (I’m subtle, aren’t I.)
How To Replace Bathroom Sink Drain?
Reach behind your drain and unscrew the cap around the pop-up ball and rod. Remove them from the drain. (FYI, if you ever have a broken pop-up, you can fix your pop-up stopper with this tutorial.)
Look under the sink and locate the P-trap. Loosen the slip nuts from the p-trap near the wall and on the drain. (For more details, you can see this tutorial for removing the p-trap.)
Use your pliers to loosen the nut on the drain and remove it. If the nut is stuck, spray a little WD-40 on it and wait about 10-15 minutes.
How To Replace A Bathroom Sink Stopper
Insert the flange collar into the top of the sink (I didn’t use plumbers putty under the flange because there was a gasket that fit under the collar, but your directions may call for plumber’s putty. Be sure to follow the directions for your specific drain installation.) The rest of the drain assembly is inserted into the sink through the bottom.
Check underneath for any signs of water. Tighten the nut if you do see any drips. Make sure you have enough teflon tape on the threads.
/how-to-install-a-sink-drain-2718789-05-a2a602315a3d4d12a8ed20429230382c.jpg?strip=all)
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.OkRemoving a sink flange to replace or repair it is a reasonably straightforward DIY task that you can accomplish without any expertise. However, residue and rust buildup can often turn an easy plumbing job into a frustrating experience.
Really Old Bathroom Sink. Easy Repair Or Have To Replace?
Fortunately, there are some simple ways to remove a sink flange, even if it's firmly stuck in the assembly. Use these step-by-step instructions to remove a sink drain flange.
Before you begin, empty everything from underneath the sink and place a cushion or two on the floor for comfort. It's also worth switching off the water supply to the faucet so that you don't get a nasty surprise if someone turns the tap on while you're working under the sink.
The coupling nut is a large ring-shaped nut that joins the flange basket to the drain pipe. Grasp it firmly with a set of slip-joint pliers and twist it to the left to loosen it. If it doesn't budge, try turning it in the opposite direction. Doing this can break any residue or rust that's jamming the nut, letting you unscrew it more easily. Loosen it until you can remove it from the threads.
How To Remove 6 Different Kinds Of Drain Stoppers
Using your slip-joint pliers, twist the locknut between the flange assembly and the bottom of the sink to remove it. If the flange is rusty or caked with residue, this may cause it to spin.
Allowing the flange to spin while you loosen the locknut could lead to damage, so it's important to hold it still while you work. You can do this by inserting the handles of a pair of pliers into two of the holes in the drain basket. Place a screwdriver or other rigid tool between the handles, and ask a helper to hold it in place to stop it from turning.
Finally, you can use a utility knife to cut away any hardened plumber's putty holding the flange in place and gently pry the flange upwards. Once you've chipped away any putty causing the flange to stick, you should be able to pull it out by hand.
Drain Buddy: Bathroom Hair Catcher & Sink Stopper Solutions
Rust is one of the most common reasons people find it difficult to remove their old sink flange. One of the easiest and most effective ways to break down the rust is to spray the threading thoroughly with silicone lubricant and leave it to soften. The package should tell you how long you need to let it sit. If you still can't loosen it, try tightening the nut instead. While it may sound counterintuitive, this can break the stubborn rust and solve the issue.
If lubricant doesn't work or the issue is compounded by a thick layer of putty holding the flange in place, you may need to apply a bit more force to get it out. Place a block of wood under the sink against the bottom of the flange and hit the wood firmly with a hammer. The sudden force should be enough to break any stubborn rust or putty and loosen the flange.
Fortunately, there are some simple ways to remove a sink flange, even if it's firmly stuck in the assembly. Use these step-by-step instructions to remove a sink drain flange.
Before you begin, empty everything from underneath the sink and place a cushion or two on the floor for comfort. It's also worth switching off the water supply to the faucet so that you don't get a nasty surprise if someone turns the tap on while you're working under the sink.
The coupling nut is a large ring-shaped nut that joins the flange basket to the drain pipe. Grasp it firmly with a set of slip-joint pliers and twist it to the left to loosen it. If it doesn't budge, try turning it in the opposite direction. Doing this can break any residue or rust that's jamming the nut, letting you unscrew it more easily. Loosen it until you can remove it from the threads.
How To Remove 6 Different Kinds Of Drain Stoppers
Using your slip-joint pliers, twist the locknut between the flange assembly and the bottom of the sink to remove it. If the flange is rusty or caked with residue, this may cause it to spin.
Allowing the flange to spin while you loosen the locknut could lead to damage, so it's important to hold it still while you work. You can do this by inserting the handles of a pair of pliers into two of the holes in the drain basket. Place a screwdriver or other rigid tool between the handles, and ask a helper to hold it in place to stop it from turning.
Finally, you can use a utility knife to cut away any hardened plumber's putty holding the flange in place and gently pry the flange upwards. Once you've chipped away any putty causing the flange to stick, you should be able to pull it out by hand.
Drain Buddy: Bathroom Hair Catcher & Sink Stopper Solutions
Rust is one of the most common reasons people find it difficult to remove their old sink flange. One of the easiest and most effective ways to break down the rust is to spray the threading thoroughly with silicone lubricant and leave it to soften. The package should tell you how long you need to let it sit. If you still can't loosen it, try tightening the nut instead. While it may sound counterintuitive, this can break the stubborn rust and solve the issue.
If lubricant doesn't work or the issue is compounded by a thick layer of putty holding the flange in place, you may need to apply a bit more force to get it out. Place a block of wood under the sink against the bottom of the flange and hit the wood firmly with a hammer. The sudden force should be enough to break any stubborn rust or putty and loosen the flange.
0 Comments
Posting Komentar