Ever heard of a sink drain flange? This component plays an important role in your kitchen or bathroom sink's drain assembly. A leaky sink drain flange needs to be replaced quickly to avoid water damage to your home.
Fortunately, this is an easy repair, even if you don't have much DIY experience. Here’s how to install a sink flange, plus some tips on removing your old flange from the drain hole.
A sink flange connects the sink drain to a section of pipe called a tailpiece to create a tight seal. It is made of metal and sits around the edge of the drain rather like a collar, and it usually has a grid-like section covering the drain that looks like a strainer. The sink drain flange prevents water from leaking out of the plughole when you run the faucet. If it becomes damaged or loose, water can leak into the area under the sink.
Blocked Sink Clearance
If you're installing a sink drain flange for the first time, start by making a thin sausage shape out of plumber's putty between your hands and place it around the perimeter of the drain opening. The putty should be around 0.25 inches thick.
Next, press the new flange firmly into the hole and follow the manufacturer's instructions for securing it in place. Most new sink drain flanges come with a nut and washer that you'll need to screw on. Start screwing them on by hand, then use pliers until you can't tighten them any further. Before moving onto the next stage, check that the edge of the flange sits flat against the bottom of the sink.
Finally, use a cloth to wipe off any excess putty that's been pushed out from under the seal. You can now attach the bottom of the flange to the tailpiece under the sink.
How To Change A Kitchen Sink Drain: In Four Easy Steps |
Before you replace your sink drain flange, you'll need to disconnect the old flange from the tailpiece. You can usually unscrew a plastic tailpiece by hand, but a metal tailpiece needs more elbow grease. Use a wrench to unscrew a metal tailpiece. It's a good idea to switch off the water supply to the faucet before you start working to avoid a nasty surprise if someone unwittingly turns the tap on.
Next, unscrew the large nut holding the sink drain flange in place. If it won't budge, spray it liberally with silicone lubricant and leave it for a few minutes before trying again. If it's still stuck, try tightening the nut before loosening it. This can help break any stubborn rust holding it in place.
Once you've removed the nut, push the flange up firmly from underneath the sink until it pops free of the drain hole. Use a putty knife to scrape away any dried-on plumber's putty before installing a new sink drain flange using the instructions above.
Sink Drain Cleaner Drain Clog Remover Drain Dredging
The steps for removing a bathroom sink drain flange are the same as removing a flange from a kitchen sink. However, some bathroom sink drains have a stopper attached. You'll need to unscrew and remove the stopper before you can push the sink flange out of the drain hole.This article was co-authored by David Balkan. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award.
If your kitchen sink drain is corroded and leaking, installing a new basket strainer is an easy way to solve the problem. Start by adding plumber’s putty to the underside of the basket strainer and fit it into the drain hole at the bottom of the sink. Then, tighten the nut with a basket wrench to secure it in place. You can then fit a brass tailpiece onto the bottom of the basket strainer, reconnect the drainpipes, and you’re done!
This article was co-authored by David Balkan. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award. This article has been viewed 181, 519 times.
Homer 3 1/2 Kitchen Sink Drain Assembly With Strainer Basket/drain Stopper Replace, Sink Strainer Drain, Steel Strainer Basket And Drain Stopper Replacement For Standard Kitchen Sink.
To install a kitchen sink drain, you’ll need a drain assembly kit that fits your sink, pliers, a basket wrench, plumber’s putty, and a brass tailpiece to attach the basket strainer to the main drainpipe. You’ll need to disconnect the drain pipe and remove the existing strainer if you haven’t already. Once it’s removed, you’ll need to apply some plumber’s putty to the underside of the new basket strainer to connect it to the drain hole. You’ll then need to tighten the nut on the bottom of the basket to create a watertight seal. When everything’s in place, you can take a brass tailpiece and use a connector ring to attach it to the main pipe. For more advice, like how to test your new drain, read on!
The steps for removing a bathroom sink drain flange are the same as removing a flange from a kitchen sink. However, some bathroom sink drains have a stopper attached. You'll need to unscrew and remove the stopper before you can push the sink flange out of the drain hole.This article was co-authored by David Balkan. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award.
If your kitchen sink drain is corroded and leaking, installing a new basket strainer is an easy way to solve the problem. Start by adding plumber’s putty to the underside of the basket strainer and fit it into the drain hole at the bottom of the sink. Then, tighten the nut with a basket wrench to secure it in place. You can then fit a brass tailpiece onto the bottom of the basket strainer, reconnect the drainpipes, and you’re done!
This article was co-authored by David Balkan. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award. This article has been viewed 181, 519 times.
Homer 3 1/2 Kitchen Sink Drain Assembly With Strainer Basket/drain Stopper Replace, Sink Strainer Drain, Steel Strainer Basket And Drain Stopper Replacement For Standard Kitchen Sink.
To install a kitchen sink drain, you’ll need a drain assembly kit that fits your sink, pliers, a basket wrench, plumber’s putty, and a brass tailpiece to attach the basket strainer to the main drainpipe. You’ll need to disconnect the drain pipe and remove the existing strainer if you haven’t already. Once it’s removed, you’ll need to apply some plumber’s putty to the underside of the new basket strainer to connect it to the drain hole. You’ll then need to tighten the nut on the bottom of the basket to create a watertight seal. When everything’s in place, you can take a brass tailpiece and use a connector ring to attach it to the main pipe. For more advice, like how to test your new drain, read on!
0 Comments
Posting Komentar