Hi guys today we have a look at how to install a kitchen sink waste trap and pipe on a bowl and a half kitchen sink i show you how to fit the kitchen waste
The curved pieces of drain pipe underneath your sink commonly referred to as p traps do a lot of dirty work over time they leak become corroded or get pl
Hold the p trap with the curved portion of the pipe pointing down slowly push the straight end of the trap arm into the waste pipe continue pushing the trap arm deeper into the pipe until the opening on top of the j pipe is directly underneath the drain in the sink basin rotate the j pipe if you need to
How to install sink drain pipe photo 1 connect the tailpiece to the strainer attach the tailpiece to the basket strainer but don t fully tighten it yet you ll have to remove and cut it later how to install sink drain pipe photo 2 place the trap arm under the tailpiece slide the trap arm into the adapter
1 turn off the water supply locate the shut off valve under your sink and turn it clockwise to shut off the water supply this step is crucial to do before beginning work to avoid accidental leaks 2 remove the existing p trap if applicable if an old p trap is in place use your adjustable wrench to loosen and remove the nuts securing it
Slide a slip nut and washer onto the straight end of the trap arm push the trap bend up into the tee fitting on the tailpiece while sliding the trap arm into the drain outlet at the wall adjust the trap pieces as needed to create the most direct path from the sink to the drain outlet
Several sizes pipe diameters are available including 1 1 4 inch 1 1 2 inch and 2 inch bathroom sinks usually use 1 1 2 inch traps while kitchen sinks usually use 2 inch traps washers are provided that allow you to connect to the 1 1 4 tailpiece from a sink 2 inch traps are commonly used on shower and tub drains
How to tighten the coupling nuts open the jaws of the pliers wide enough to grip the coupling nut tighten the nut by gently turning it clockwise until it s snug apply strong pressure but don t strip the threads by over tightening on a metal trap tighten the coupling nuts hand tight plus about a half turn using slip joint pliers to
Easily replace your basin waste trap and avoid wasting water with this quick diy shop yours online bit ly 32gcdjp
Assemble the trap adapter onto the sink drain tailpiece cut and dry fit lengths of pvc pipe to connect the trap adapter to the trap and the drain elbow to the waste line swivel the trap or slide it on the tailpiece to fine tune the pipes lengths and alignment take the drain pieces apart clean off the cut ends with a utility knife
Press the rubber seal onto the square section leading to the pipe hold the seal in place while threading a screw through from the sink side to secure it adding the sink trap install your sink waste trap ensuring a secure connection to the sink drain sink traps often come with an additional spout perfect for connecting a washing machine or
1 attach a brass tailpiece to the bottom of the basket strainer take a brass tailpiece and line up the threads with the threads on the bottom of the basket strainer screw on the tailpiece as tightly as you can with your hands you can find brass tailpieces at hardware stores and home improvement stores
Install the pvc drain line the sanitary tee and the p trap for the sink the appropriate coupling for the aav glued or threaded attaches to the tee check the manufacturer 39 s instructions and local codes to determine the proper height for the aav above the drain how to draw a plumbing plan for your next remodeling project
Step 1 remove existing garbage disposer first unplug the garbage disposer from the wall socket if you don t have access to unplug it then turn off electrical power at the circuit breaker or fuse box next unscrew the coupling nut from the drain trap that holds the waste discharge tube
Disconnect the drain trap from the discharge tube also disconnect the tubing from the dishwasher inlet step 3 follow these steps to release the disposal from the mounting ring found towards the top of the unit step 4 if your disposal is wired directly remove the cover plate and disconnect the wires how to install a new garbage disposal
How to fit a new kitchen sink waste and dual inlet appliance trap to connect up a washing machine and dishwasher i used these parts mcalpine sink waste and o
First make sure the trap arm extends no more than 24 inches from the trap to the waste line longer than that and you might need a handyman hotline fit the trap s curved section to the sink s tailpiece think of it as connecting the dots but with a slight twist align the trap arm with the waste line inlet
Types sizes explained p trap is a p shaped bend pipe used in drainpipes to connect your sink 39 s drain directly to the sewer system or septic tank in usual circumstances p traps always retain some water they are made of cast iron sheets or upvc and have a robust water seal
Push the bent hanger down the drain then twist and pull until you feel it hook onto the baffle now wiggle it up and down while twisting it to remove the clog run water in the clogged sink to tell if you ve removed the obstruction if the sink still doesn t drain there s a clog farther down move on to the next step
How to install p trap on double sink step 1 connect the drain tailpieces the first step in installing a p trap on a double sink is to connect the drain tailpieces make sure that the drain tailpieces are at an equal height for both basins use a pvc cutter or a hacksaw to mark and cut accordingly then fit the drain tailpieces to the basket
In this viva tv video we explain how to install a basket strainer sink waste with and with out overflow including installing a square overflow for more in
Once you have chosen a suitable model follow these steps for installation 1 turn off the water supply locate the shut off valve under your sink and turn off both hot and cold water supplies 2 remove cabinet panel remove any panels or drawers beneath where you plan to install your dishwasher 3
0 Comments
Posting Komentar